Yes you guys can upgrade your TF1260 with the new 999 firmware yourselves if you have xilinx programmer or with raspberry pi

https://www.exxoshost.co.uk/forum/vi...hp?f=75&t=4600

Hi Jungo. Thank you for your effort! I am wondering how it is possible, that you have 6.5MB/s. I have only 1,6MB/s. It is possible, that you have the last beta FW?

Abych pravdu řekl, spíš koukám po Vampire 4+ SA. Ten bych totiž mohl používat denně na rozdíl od Amči, která mi odpočívá ve vitríně a pouštím ji jen o narozeninách svých dětí místo dortu

To nemam, ja toho zas tak moc nemam celkove, jsou tady na to jiny experti. Ja jsem vybaven tak primerene. A TF1260 nestaci? Kdyz netrvas na 60 rev 6, tak jine jsou celkem dostupne.

Hele Dodíku a nemáš nějakou 040 A1200 turbínku, kterou bys oželel. Klidně i bez CPU 😉

RTC si das na clockport, FPU je s 68030 sotva nejak efektivne vyuzitelne a 64MB RAM uplne v pohode, to musi stacit kazdemu

Jako s tou cenou mi vyrazil dech. Myslím, že Jens nemůže konkurovat. Jasně, má to nevýhody, nelze osadit FPU, nemá RTC nebo slot na RTC a má jen 64MB RAM. Ale za tu cenu je to bomba.

Pekny, kdyz ja tech turbin mam uz asi dost. Skoro to vypada, ze tech turbin je uz vic jak A1200, ktere jsou nejak nedostatkove.

TF1230 je hotová a Alen z Kanady je prodává za 160$ včetně CPU 68030/50MHz. Obsahuje 64MB RAM a IDE port jako na TF1260.

Hi Jungo

Congratulation to working TF IDE and Yes , speed is enough and Maybe with new fw, will be much faster yet. We will see.

Sorry it is English but here is some pointers on how to get the ehide.device working on your TF1260 by Trixter on Exxos

I had a go at using the TF1260's IDE header this evening - 6.5MB/s, that's pretty fast!

One thing to remember if you're going to do this - make sure anything you're already using Loadmodule for on your primary CF card (ie the one that's going to move onto the TF1260) is copied across to the CF card on the internal IDE header that's being used to load ehide.device. Loadmodule can only be invoked once during boot, so anything that you want made resident by a Loadmodule command in the startup-sequence of the primary CF will be ignored. You'll have to copy across libraries and modules to the boot CF card and add them to the boot CF's startup-sequence Loadmodule command.

As an example, my Loadmodule now looks something like this:

Loadmodule >NIL: DEVS:ehide.device DEVS:Modules/icon.library LIBS:workbench.library LIBS:intuition.library LIBS:mathieeesingbas.library LIBS:mathffp.library

anything after this (ie setpatch, assigns, the setting up of env doesn't get run because the machine immediately reboots following Loadmodule. Startup-seqeuence then begins on ehide.device (which is now your primary boot cf card) but a loadmodule command here is ignored because loadmodule has already been invoked (and libraries / modules made resident) previously.

Of course, I’m sure you could use If and Else to get around this, but I’ve never been clever enough to work them out!

The last thing to do is make the primary CF card have a higher boot priority than the boot CF card. This is done using something like HDToolbox. The boot CF will have priority 0 by default, so set the primary cf as 1. Floppy is 5, so that will boot in preference to any HD

Falcon_11 Tak už to fachčí . Načetlo to již CF kartu z IDE na TF1260, což je super, jelikož to budu využívat jako data disk. Akorát tu kartu nevidí HDToolbox

Jj,, ma to napísané pri tých obrázkoch

Cyberian - to je v Infinitive Toweru?

Nikde to tu nepíšeš, ale musíš pomocou LoadModule nahrať ten ehide.device v podstate do Pamäte , ešte pred Setpatchom. Akorat, nahrať do pamäte to musíš najprv tak, že bootovat musíš z interného IDE, ale ked to bude už v pamäti, tak to štartuje z toho TF-ide.